VyOS with ESXI 6.7

Prerequisites

To complete this tutorial, we will need:

• 1 node running ESXI. This tutorial is done on a node running EXSI 6.7
• 1 VM running the VyOS
• 4 testing VM's on separate VLAN's

Objective

Our Goal is to be able to create the network in the image below. Note that we are not going to discuss about how to use ESXI in this tutorial but we will be more focus on VyOS and how to use it to connect to the vswitches on the ESXI node.

Creating VSwitches and port groups on the EXSI server=

The Vswitch0 is already create and has two port groups already: "VM Network" and "Mangement Network" so we are not going to worry about this.

Create VSwtich

In this section, we will be creating 4 Vswithes called:

- asw-a-codfw

- asw-b-codfw

- asw-c-codfw

- asw-d-codfw

Do not assign any up-links to the Vswitches. Like a mentioned above we are not going to discuss how to create Vswithes in this tutorial. After you have created the 4 Vswitches above, the next step will be to create the port groups in the nest section.

Create Port groups

create 4 port groups like in the table below.

Port Groups

Port name	vlan	vswitch
private1-a-codfw	20	asw-a-codfw
private1-b-codfw	30	asw-b-codfw
private1-c-codfw	40	asw-c-codfw
private1-d-codfw	50	asw-d-codfw

VyOS installation and configuration

Installation

The installation of VyOS is simple and easy. It is done like a regular VM installation on ESXI.

• First : create a VM with

- Name:vrouter4001 ( You can use any name)

- 1024MB of RAM

- 1 CPU

- 40GB of Disk

- 5 Network Interfaces

Network Interfaces and port groups

NIC	Port Group
eth0	VM Network
eth1	private1-a-codfw
eth2	private1-b-codfw
eth3	private1-c-codfw
eth4	private1-d-codfw

• Second: Download the iso image

The Link to download the iso is: https://downloads.vyos.io/?dir=release/legacy/1.1.8

Download the vyos-1.1.8-amd64.iso version

• Third: attache the iso to your VM and boot the VM

After booting the VM, you will see the login prompt like in the image below

The default login username is vyos and the password is vyos too.

Once login, run the command

show interfaces

to make sure you have all the 5 interfaces. The output should look the same like in the image below

If you have all the five interfaces, proceed to the installation by running the command

install image

Follow the instructions on the screen bu just pressing enter and answering "YES" to all the question to use the default settings. Don't forget to enter a new password for login to replace the defaut password "vyos"

Once the installation completed, power off the VM, detach the iso image from the VM and power backup the VM and proceed to the configuration.

Configuration

Setting IP addresses and description

eth0

configuration
set interfaces ethernet eth0 address 10.192.0.53/24
set interfaces ethernet eth0 description core_to_cr-gcsm

eth1

set interfaces ethernet eth1 address 10.192.16.1/22
set interfaces ethernet eth1 description private1-a-codfw

eth2

set interfaces ethernet eth2 address 10.192.32.1/22
set interfaces ethernet eth2 description private1-b-codfw

eth3

set interfaces ethernet eth3 address 10.192.48.1/22
set interfaces ethernet eth3 description private1-c-codfw

eth4

set interfaces ethernet eth4 address 10.192.64.1/22
set interfaces ethernet eth4 description private1-d-codfw

commit
save

Note: if you do not "save", after a reboot all the configuration will go away.

check the configuration with "show interfaces"

vyos@vyos:~$ show interfaces 
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface        IP Address                        S/L  Description
---------        ----------                        ---  -----------
eth0             10.192.0.53/24                    u/u  core_to_cr-gcsm 
eth1             10.192.144.1/22                   u/u  private1-a-codfw 
eth2             10.192.160.1/22                   u/u  private1-b-codfw 
eth3             10.192.176.1/22                   u/u  private1-c-codfw 
eth4             10.192.192.1/22                   u/u  private1-d-codfw 
lo               127.0.0.1/8                       u/u  
                ::1/128

Go back in configuration mode and change the router name from vyos to vrouter4001 ( you can call it anything)

set system host-name vrouter4001
commit
save
vyos@vrouter4001:~$

Setting default gateway

If we do not define the default gateway, all the VM's will not be able to access the internet.